Rubber Coat®

Rubber Coat® is a modified elastomeric asphalt emulsion specifically formulated for application by brush, squeegee or roller. Rubber Coat® is a cold applied, single component product that yields a membrane with excellent strength, elasticity and adhesion. Rubber Coat® is an environmentally friendly waterproofing product that can be applied indoors and outdoors with conventional protective equipment.*

BRUSH GRADE
Property Typical Results
Specific gravity (liquid) g/cm3 Approx. 1.0
Odor None
VOC Contains no solvents
Color Brown to black
% solids (wt) 53-58
Viscosity, Brookfield, sp. #5, 20 rpm 8000-9000
pH 10-12
PERFORMANCE (Cured membrane)
Property Typical Results
Color Black
Specific gravity g/cm3 Approximately 1.0
Chemical resistance Resistant to most inorganic solutions. Not recommended for gasoline or other petroleum products. Consult Chemical Resistance chart for further information.
Biological resistance ASTM E 154, ASTM 0412 Passed (> 90% original value)
Impact resistanceCSB37-GP-500 23oC, in-lbs Passed (168)
Water tightness after impact Passed (no leakage)
Water tightness CGSB 37-GP-56 Zero Leakage
Tensile strength ASTM 0412, psi 90
Elongation, % 850
Accelerated weathering, ASTM G 155,0 412 Passed (No deterioration of film)
Tensile strength Passed (> 90% original value)
Hardness, Durometer Type 00 85-87
Salt Fog Corrosion, Steel ASTM D412 1000 hours passing
SurfaceCorrosion ASTM D610 No Corrosion after 500 hours,
0.03% after 1000 hours
Adhesion to concrete ASTM C907 111 PSI
Hardness ASTM D2246 50 Type A
Puncture resistance CGSB 37-GP-56 No perforations
Water Vapor Transmissions ASTM E96 0.04
APPLICATION

Rubber Coat® is a water-based, environmentally safe alternative to conventional hot-applied, solvent based and sheet membrane waterproofing systems. Since Rubber Coat® cures by evaporation, a minimum application temperature of min. 40oF (4.5oC) is required. Apply in thin coats. The product cures within 24-48 hours at 70oF (21oC) and 50% relative humidity, at a thickness of 40 mils (1mm).

For best results, surfaces must be dry and free of dirt, debris, oil or grease. Application is not recommended if rain is imminent, or in high humidity environments.

Rubber Coat® is applied between 20-30 ft2/gal (0.3-0.7 m2/litre) to produce a 40-60 mil (1-3 mm) protective membrane. Rubber Coat® dries to the touch within minutes at 70oF (21oC). Curing time will vary depending on temperature and relative humidity.
LIMITATIONS

*Rubber Coat® is mildly alkaline. When applying this product observe appropriate safety precautions, wear gloves, eye protection and other suitable protective equipment. For further information please consult the product MSDS.

Rubber Coat® should not be applied when the ambient temperature is below 40oF (4.5oC). The uncured membrane may be damaged if frozen. Some surface base coats, such as coal tar are unsuitable for use with Rubber Coat®.
CAUTION

For industrial use only. Keep out of reach of children. Avoid storage below 40oF (4.5oC). Please consult the MSDS before using Rubber Coat®.
thumbnail

Rubber Coat® is PermaDri’s brush-grade coating for all waterproofing and corrosion protection purposes. Rubber Coat® is a modified asphalt emulsion that results in a rubberized membrane when cured.  Rubber Coat® has impressive flexibility and can elongate up to 850% with 98% recovery. Therefore, Rubber Coat® has the capability to accommodate for surface shifting and thermal changes without cracking and is also self-healing if punctured. Rubber Coat® is simple to apply using a brush, roller, or squeegee and adheres to virtually any surface: wood, metal, foam, concrete, tile, and more! Rubber Coat® is a cold-applied liquid that contains no volatile organic compounds- thus greatly minimizing the risk of injury or harmful effects during application.

Applications:
Download:

MSDS/Fact Sheet

©2012 PermaDri Incorporated | 4595 West Jacquelyn Avenue, Fresno, CA 93722 | 800.279.5604 | Contact Us